Chapter 677： Installation (on)

Seeing Guo Tailai wearing a pair of rubber gloves, he immediately picked up a few small parts and started assembling. Han Academician and two experts directly opened their eyes. What is this?

Guo Tailai's hand is too fast, they just reacted, Guo Tailai has assembled a blade, and even the fixed screws are good.

"Stop! Stop! Stop!" The academician of Han is going out of his chest. Isn't this a bad thing? This new and good engine is so messy: "The screws that fasten the blades have torque requirements!"

"I know that the requirement for this part is 1.2 Nm." Guo Tailai replied casually, then pointed to the wall of the studio wall with a pile of cabinets against the wall: "There is a torque screwdriver, you can measure it. In addition, the demolition I have made a record of the torque of each part at the time of solution, and it is not wrong."

The youngest expert ran straight away without thinking about it. He quickly picked up an electronic torque screwdriver with a liquid crystal screen. When he was about to measure, he found that he was picking tools one by one. At the time, Guo Tailai had already assembled five blades.

General Han’s Han and another expert stunned and watched Guo Tailai’s hand as the same speed in the movie. All the things in his hand were stable and rooted, and Guo Tailai’s movements were accurate. Surprisingly, when others look at the screw holes, the tools in his hand have been precisely screwed in.

"Don't look at it!" Guo Tailai started to work, while still not forgetting to remind the younger expert: "These have been completed, the torque of the screws are all 1.2 Nm, the error will not exceed one in a million. ""

Other than the general, the others did not believe it. The young expert took a blade that had been assembled and carefully measured it. It turned out to be Guo Tai’s figure, and there was no difference. The young expert glimpsed, and then took the second one, one measurement, still the same, five tests, all of them. In the time of his measurement, Guo Tailai has completed the assembly of seven separate blade structures. That is to say, light is the time to measure the torque of the screw, and the work is faster than the measurement.

“The dimensional tolerances of the assembly should also be within 10 microns, but their original engineers are a little perfunctory, and several of them are not so well-standardized.” Guo Tailai’s words did not stop when he was working: “Maybe I feel that I have to send it to our country, so it doesn't matter if it is a little bit worse."

When everyone saw Guo Tailai's screw that was twisted twice with a torque screwdriver and it was unbelievable when it was unpredictable, no one said anything more, only listening, and sometimes bowing down.

“Don’t remember.” Guo Tailai saw it and immediately reminded: “I have already finished drawing the whole set of drawings, and the installation specifications are also completed. All of them have detailed labels. When they are taken away, they will be taken away.”

Less than ten minutes ago, the academician of the South Korean still suspected that Guo Tailai had only spent a day to finish the paintings. He was perfunctory, but now he can't wait for Guo Tailai to finish all. Because from the beginning to the present, Guo Tai’s data is a little bit of experience that they used to explore for more than ten years. It can only be used in Guo Tailai for less than a day.

Within fifteen minutes, four people watched Guo Tailai begin to assemble the first impeller piece. Then there is the second, the third...to the last one. Next is the engine casing, the main shaft, several thin shafts, connected to a series of blades, various lengths of fuel injection nozzles, in series, in series, most of which are repeated work.

Although the repetition seems simple, it is not so easy to achieve the accuracy of the assembly. Normal assembly, it can be said that every time a blade is installed, it has to be measured many times and adjusted many times. Where is it like Guo Tailai? In the eyes of many senior engineers, it takes a lot of patience and careful assembly work. Here, Guo Tailai is as simple as riding a Lego block. However, the things he took out with his hand, measured with a variety of sophisticated tools, found that the measurement accuracy of the most accurate tools that can be used here is more accurate, which is reasonable?

"The processing of these parts, our current processing capacity, should also be able to be made." Guo Tailai's mouth has not stopped in the process of working: "The only thing that is bad now is the material. However, the problem of materials It can't be solved immediately, only slowly. Others can use five thousand hours, we use 500 hours first, others can withstand one thousand five hundred high temperature, we first bear one thousand three Baidu, first solved No problem, then come to excellence. And the material is based on accumulation. It must be clear that several teachers are better than me. I can provide some help in processing and assembly, and others can't help anything. ”

General Yan looked at the watch and started to install it from Guo Tailai. For three and a half hours, Guo Tailai’s hand was always so stable, fast and precise, without any fatigue, and the rhythm was almost more accurate than those of the band’s drummer. Only this point, no one in China can match Guo Tailai, the most powerful warrior of the whole army, I am afraid that Guo Tailai can not be expected on this item. Master, there is no reason.

However, Guo Tailai stood on the other side of the platform, and kept working on his hands. The mouth was still explaining, and the three experts headed by the Korean academician had no idea before. The kind of heartache, only the modest and eager to concentrate, can not record all of Guo Tai's explanation, and Guo Tailai always reminds them not to remember, he has written detailed procedures.

I don't understand a bit in the middle. As long as they ask, Guo Tailai will explain it in great detail. Academician Han is an expert in this area, but in the processing and assembly, even Guo Tailai's taillights are not visible.

Nearly four hours later, Guo Tailai patted his hands and pointed to both sides. When everyone looked at it, it was discovered that the neatly-packed parts of the platform that had been dismantled by Guo Tailai all disappeared at the moment. In other words, they are all installed in the front of the turboshaft engine. According to their entire observation of Guo Tailai's assembly process, there is no more small parts, and there is no less than a small part, just right.

"In fact, it is still more." Guo Tailai smiled and pointed to a small device placed on another platform: "The few self-destructing devices, I will not put it in. After watching this for a long time, hungry? Go ,go for meal!"